SayPro Compile required records related to handling and using materials or resources and submit reports.

When manually moving materials, employees should seek help when a load is so bulky it cannot be properly grasped or lifted, when they cannot see around or over it, or when a load cannot be safely handled.When an employee is placing blocks under raised loads, the employee should ensure that the load is not released until his or her hands are clearly removed from the load. Blocking materials and timbers should be large and strong enough to support the load safely. Materials with evidence of cracks, rounded corners, splintered pieces, or dry rot should not be used for blocking.Handles and holders should be attached to loads to reduce the chances of getting fingers pinched or smashed. Workers also should use appropriate protective equipment. For loads with sharp or rough edges, wear gloves or other hand and forearm protection. To avoid injuries to the hands and eyes, use gloves and eye protection. When the loads are heavy or bulky, the mover should also wear steel-toed safety shoes or boots to prevent foot injuries if the worker slips or accidentally drops a load.When mechanically moving materials, avoid overloading the equipment by letting the weight, size, and shape of the material being moved dictate the type of equipment used for transporting it. All materials handling equipment has rated capacities that determine the maximum weight the equipment can safely handle and the conditions under which it can handle those weights. The equipment-rated capacities must be displayed on each piece of equipment and must not be exceeded except for load testing. When picking up items with a powered industrial truck, the load must be centered on the forks and as close to the mast as possible to minimize the potential for the truck tipping or the load falling. A lift truck must never be overloaded because it would be hard to control and could easily tip over. Extra weight must not be placed on the rear of a counterbalanced forklift to offset an overload. The load must be at the lowest position for traveling, and the truck manufacturer’s operational requirements must be followed. All stacked loads must be correctly piled and cross-tiered, where possible. Precautions also should be taken when stacking and storing material.Stored materials must not create a hazard. Storage areas must be kept free from accumulated materials that may cause tripping, fires, or explosions, or that may contribute to the harboring of rats and other pests. When stacking and piling materials, it is important to be aware of such factors as the materials’ height and weight, how accessible the stored materials are to the user, and the condition of the containers where the materials are being stored.All bound material should be stacked, placed on racks, blocked, interlocked, or otherwise secured to prevent it from sliding, falling, or collapsing. A load greater than that approved by a building official may not be placed on any floor of a building or other structure. Where applicable, load limits approved by the building inspector should be conspicuously posted in all storage areas.When stacking materials, height limitations should be observed. For example, lumber must be stacked no more than 16 feet high if it is handled manually; 20 feet is the maximum stacking height if a forklift is used. For quick reference, walls or posts may be painted with stripes to indicate maximum stacking heights.Used lumber must have all nails removed before stacking. Lumber must be stacked and leveled on solidly supported bracing. The stacks must be stable and self-supporting. Stacks of loose bricks should not be more than 7 feet in height. When these stacks reach a height of 4 feet, they should be tapered back 2 inches for every foot of height above the 4-foot level. When masonry blocks are stacked higher than 6 feet, the stacks should be tapered back one-half block for each tier above the 6-foot level.Bags and bundles must be stacked in interlocking rows to remain secure. Bagged material must be stacked by stepping back the layers and cross-keying the bags at least every ten layers. To remove bags from the stack, start from the top row first. Baled paper and rags stored inside a building must not be closer than 18 inches to the walls, partitions, or sprinkler heads. Boxed materials must be banded or held in place using cross-ties or shrink plastic fiber.Drums, barrels, and kegs must be stacked symmetrically. If stored on their sides, the bottom tiers must be blocked to keep them from rolling. When stacked on end, put planks, sheets of plywood dunnage, or pallets between each tier to make a firm, flat, stacking surface. When stacking materials two or more tiers high, the bottom tier must be chocked on each side to prevent shifting in either direction.When stacking, consider the need for availability of the material. Material that cannot be stacked due to size, shape, or fragility can be safety stored on shelves or in bins. Structural steel, bar stock, poles, and other cylindrical materials, unless in racks, must be stacked and blocked to prevent spreading or tilting. Pipes and bars should not be stored in racks that face main aisles; this could create a hazard to passers-by when supplies are being removed.Please visit our website at www.saypro.online Email: info@saypro.online Email: info@saypro.online Call: + 27 11 071 1903 WhatsApp: + 27 84 313 7407. Comment below for any questions and feedback. For SayPro Courses, SayPro Jobs, SayPro Community Development, SayPro Products, SayPro Services, SayPro Consulting, and SayPro Advisory visit our website to www.saypro.online