Your cart is currently empty!
SayPro Assemble a single-user personal computer and peripherals from modules.
2.1 The assembly ensures that the hardware is assembled according to manufacturer’s specification.Step One: Mount Your Motherboard
To start, open up your case’s box, take out the case, and open it up. Usually this involves unscrewing a few thumb screws on the back of your case and sliding the side panels off. Take a good look around your case and get acquainted; note where the hard drive bays are, where your CD drive will go, whether the power supply mounts on the top or the bottom, and so on. There should also be a bag of screws inside your case; grab that now and set it aside because we’ll need it in a few minutes.Open up your motherboard box and take out the I/O shield, which is the metal plate that protects the ports on the back of your motherboard. You should see a rectangular space in the back of your case where this should go. Snap it into place. This takes quite a bit of force, so make sure all four sides are snapped in securely. Next, pull out your motherboard and line up the ports on the back with the I/O shield. You should see that the holes on your motherboard line up with screw holes on the bottom of your case. There are probably more holes on your case than there are on your motherboard, so note which ones these are, and grab your motherboard standoffs from your bag of screws (they have a male screw end on one side, and a female screw hole on the other side). Screw the standoffs into those holes, and set your motherboard on top of them. Screw your motherboard screws into the standoffs so the motherboard is snugly mounted.Note: Many of you have mentioned that you prefer to install the processor, cooler, RAM, and power supply before mounting the motherboard in the case. I’ve never done this myself, but in some cases, this may be simpler and save you some digging around in your case.Step Two: Install Your Processor
Open up your processor’s box and gently take it out. Your processor is one of the more fragile parts of the build, so this is one step in which you’ll want to be careful. Find the corner of your processor that has a gold arrow on it, then look at your motherboard’s processor socket for a similar arrowed corner. Line these two arrows up; this is the direction your processor will go into the socket. Lift up the lever on the processor socket and put your processor in (Intel motherboards might also have a cover you have to lift up first). Pull the lever down to lock it into place. Again, do this gently—it shouldn’t require any feats of strength on your part, so if it isn’t falling into place easily, something’s wrong. Take it out and try re-setting it, make sure your two arrows are lined up, and of course, double check that your motherboard and processor are of the same socket type.Once your processors in, grab the cooler that came with your processor (remember, if you got an OEM processor you have to buy a cooler separately). It should already have some silver thermal paste on the bottom. If not, you’ll need to pick some up from the computer store and put a very thin line on your processor—. If you have an Intel cooler, you’ll need to press down on the four pins until the click, and then twisting the top of the peg so they lock into place. You can find more info on this in your processor’s manual (it takes a few tries, trust me). AMD coolers, like the one in the above video, are much easier—just hook the two latches on the sides onto the motherboard’s square pegs, and pull the lever down to lock it into place.Step Three: Install Your RAM
Installing RAM is very simple. Find the RAM sockets on your motherboard, and pull the two clips on the side down. Line up the notch in your RAM stick with the notch in the socket, and press the RAM down into place. This might take a bit of pressure, so don’t worry about being overly gentle. The clips should snap back into place when the RAM is fully in the socket.Step Four: Install Your PCI CardsFor your video card (or any other PCI expansion card), find the topmost slot that fits your card and match that up with its plate on the back of the case. Remove that plate and slide the PCI card’s bracket in its place. The card should then be sitting on top of the socket, and all you need to do is press down to lock it into place. Screw the bracket onto the case, and you’re good to go. Note that if you need to remove it for any reason, there may be a small lever on the back of the socket you need to press before you pull it out.Step Five: Install Your Hard DriveEvery case is a little bit different in how they install hard drives. Generally, there are two methods: on some cases, you have to pull out a hard drive tray, put the drive in, screw it in securely, and then slide the tray back in. Other motherboards just require you to slide the bare drive into the bay and then screw it in snug after the fact. Check your case’s manual for more detailed instructions on this particular step.If you’re using multiple hard drives and a big case, it’s usually a good idea to leave some open space between them—that is, putting them in the first and third bays instead of first and second. This allows for more airflow between them and will help keep them running cool.Step Six: Install Your Optical DriveThe optical drive should be pretty self-explanatory. Just pull out the plastic cover on one of your 5.25" drive bays and slide in your optical drive. Screw it into place if necessary.Step Seven: Mount Your Power SupplyOnce everything else is in, it’s time to install your power supply and plug everything in. (Note that if your case came with a power supply, you can skip this step, as it’ll already be installed). It should be pretty obvious where your power supply goes, as there will be a big rectangular hole on the back of your case. Some power supply’s mount on the top, while some sit on the bottom of the case. Generally, they mount with the fan facing away from the edge of the case, unless that case has enough space in between the power supply mount and the end of the case to allow for airflow. Once you set it into place, you should see the holes on the back of the case line up with the screw holes in the power supply. Screw it into place and you’re all set.Step Eight: Plug Everything In
This can be the most tedious and difficult part of the process, depending on your case and power supply. Separate the cords coming out of your power supply and plug them in individually.These are the ones you should have:A 24-pin Motherboard Cable: This is the biggest cable on the power supply, which gives the motherboard the electricity it needs to run. It has the very long plug with, you guessed it, 24 little pins in it. Most cases should have a 20-pin with a 4-pin on the same cable, so you can just put them together and plug them into the big 24-pin socket on your motherboard. It should lock into place, and might take a bit of strength to get it in all the way. Push it in until you hear the click and you can’t pull it out with just a slight tug.A 4-pin Motherboard Cable: You should also have a separate 4-pin cable coming out of your power supply, and a small 4-pin socket somewhere else on the motherboard. This plugs in the same way as the 24-pin cable—just push down until it locks into place.SATA Power and Data Cables: Your hard drives and optical drive plug in via SATA, which contains two cables. One is the skinny black plug coming out of your power supply, which gives power to those drives. The other is a small red cable that should have come with your motherboard; this is the SATA cable that actually transfers data between your hard drive and everything else.Plug the power cable into the long pin on your hard drive, and plug the data cable into the short pin. The sockets are L-shaped, so they’ll only go in one way. After plugging both cables into the drive, be sure to plug the other end of the data cable into your motherboard, in the sockets labeled SATA. Repeat this entire process with your optical drive.Molex Power Cables: Your Molex cables power other miscellaneous things in your build, like the case fans. Take the plugs connected to your case fans and plug the male side into the female molex cable on your power supply. This takes a bit of force to get in, and even more force to get out (seriously, these are my least favorite cables of all time). Note that some fans, like the one on your CPU, might have a smaller connector that actually plugs into your motherboard instead of the power supply instead of via Molex. The small headers will be labeled CPU_FAN or SYS_FAN. This not only gives power to your fans, but also lets you control their speed with certain programs.Front Panel Audio, USB, and FireWireConnectors: Most cases have a few ports on the front, which can include but are not limited to USB, FireWire, headphone, and microphone jacks. You should see some small cables coming out of the front of your case labeled things like USB, HD AUDIO, and 1394 (which is FireWire). Plug these into their corresponding 8pin headers on the motherboard—usually labeled USB, AUD, and 1394, or something of the sort.Power Switch and LED Connectors: Lastly, you should have a few small cables labeledPOWER SW, RESET SW, HDD LED, and so on. These connect the switches and LEDs on the front of your case to the motherboard, so you can actually turn your computer on. They all consist of only one or two pins, and all plug in on an 8-pin header somewhere on the motherboard. This varies from build to build, so you’ll have to check your motherboard’s manual to see how they all plug in. Your motherboard may also have a small speaker that plugs into an 8-pin connector, which you’ll find in your motherboard box and will be listed in your motherboard’s manual.A Note on Cable Management As you’re doing all this, you want to be wary of where you’re putting these cables. Generally, you want to keep them as out of the way as possible. The more they’re tangled up in the middle of your case, the more they’re going to block airflow from your fans, causing your computer to run hotter, louder, and possibly even overheat. Your case may have come with some zip ties to help you wrap them up and get them out of the way. Some cases even come with built-in cable management features, like clips or holes through which you route these cables to keep them out of the way. Cable management is a beast unto its own, and it differs from case to case, so it’s just something you’ll have to fiddle with.
A system with good airflow due to intelligent cable management.Turning It On When you’re done, plug in the power cable in the back, flip the power switch on, and press the power button on the front of your case. If all goes well, your computer should turn on and, if you plug a monitor into your video card (or motherboard, if you don’t have a video card), you should see what’s called the POST screen. From there, you can head into your BIOS setup by pressing a key on your keyboard (usually DEL). At this point, it’s probably time to start cleaning up.Common Troubleshooting If your computer didn’t turn on, don’t panic. First, recheck everything inside. Is your processor seated correctly? If your RAM all the way in its socket? Are your cables plugged into the right sockets? (This is a big one). Run through the entire process again to make sure you did everything correctly. If your system turns on but makes a beeping noise instead of going through the POST screen, then you have an error. If you can find your motherboard’s BIOS manufacturer (either by watching the POST screen or by searching online), you can diagnose these error codes to find out what’s wrong with your system using these pages:2.2 The assembly ensures that system and application software are customised and configured according to assembly specification.Step One: Edit your BIOS 
When you first start up your computer, it’ll tell you to press a key to enter setup, usually DEL. This takes you to the setup of your Basic Input/output System, or BIOS. Here, you can configure some of the lowest-level aspects of your new machine. You may not actually need to edit any of these settings, but it’s a good idea to go through, get acquainted with them, and make sure everything’s in good order before moving on.Note that the BIOS will be a little bit different on different brands of motherboard, so your screen may not look exactly like the images here, but it should be close.First, we should make sure that everything’s been installed correctly. If you have a System Information page in your BIOS, head there and make sure the amount of RAM listed is the same amount you put in. If it isn’t detecting all of your RAM, some of it might not be seated correctly, so go back and fix that before continuing. If there isn’t a System Information page in your BIOS, your motherboard probably lists the amount of RAM it detects on the POST screen, right after you press the power button.Find the SATA configuration option, and make sure it’s configured as AHCI. If you’re running windows XP you’ll need to change this to IDE, otherwise AHCI is probably what you want to go with.Lastly, find the "Boot Order" or "Boot Priority" page. make sure your DVD drive is the first drive on the list (or your USB drive if you’re installing from a flash drive), and that the hard drive you’ll be installing to is second. Note that some BIOS utilities split this up into two menus—one for setting the boot order for your different media (CD-ROM, hard disks, USB disks) and another that lets you choose the order of just the hard drives.If you don’t see your hard drive listed, it may not be plugged in correctly or it may be dead. Turn your computer off and re-check the connection if necessary. These are the most crucial BIOS options you want to tweak, but there’s a lot of other stuff going on in there.Step Two: Install Windows 
Next, grab your Windows installation DVD (or flash drive, if that be the case) and pop it in. Start up your computer and it should automatically boot into the Windows installer. If you ever get a "Press any key to boot from CD" option, make sure to hit a key on your keyboard to continue.Once the installer loads, hit the "Install Now" button, accept the terms of use, and choose "Custom (advanced)" when asked what type of installation you want. Find your primary hard drive (if you have more than one), click on the "Unallocated Space" partition, and hit Next. Windows should start installing.If you aren’t using a brand new drive, you may have to format it first. Click on the currently used
Partition, click "Drive options (advanced)", and then hit "Format". It should format the drive to be Windows-compatible, after which you can hit next and let the installation run.From there, the rest is just a waiting game.Leave your computer alone to do its thing. It’ll copy all the necessary files to your disk and reboot a number of times in the process. You’ll know you’re done when you hear the familiar startup chime and boot into the default Windows 7 desktop.Step Three: Install Your DriversThe last thing you need to do before you actually use your computer is install your drivers. If Your Ethernet or Wi-Fi works out-of-the-box, Windows may find most or all of your drivers for you. If not, you’ll need to pop in the CD that came with your motherboard to install the Ethernet or Wi-Fi drivers you need to access the internet. Don’t install any other drivers from that CD just yet. Once you’ve got the internet up and running, Windows will install drivers for you. It might not catch everything though, so you’ll have to install some manually. The CDs that came with your motherboard, video card, and other hardware are probably already out of date, so I don’t recommend using these to install those drivers.
Instead, you’ll want to download the drivers manually from the manufacturer’s web site. Open up Device Manager by opening up the Start menu and searching for "Device Manager". Look for anything that has a question mark or an exclamation point next to it. Often, it’ll tell you what the missing driver is for—say, SATA—and you can then head to your motherboard manufacturer’s web site, go to their support page, and download the drivers manually. If it’s your video card that’s missing a driver, you’ll want to head to NVIDIA or ATI’s web site instead. If it says "Unknown Device" next to the driver-less device, try inserting the CD that came with your motherboard and seeing if there are any drivers that aren’t listed in the Device manager, and try installing those from the manufacturer’s web site. Eventually, you should be able to get everything installed.
SayPro is a group of brands leading in Africa’s development, building innovative online solutions and a strategic institution on child growth, youth empowerment and adult support programmes, applications in Africa.SayPro Core Skills and Expertise:
SayPro is providing international and global opportunities for African youth. Partner with SayPro now by sending an email to info or give us a call at + 27 11 071 1903 |
Please visit our website at www.saypro.online Email: info@saypro.online Email: info@saypro.online Call: + 27 11 071 1903 WhatsApp: + 27 84 313 7407. Comment below for any questions and feedback. For SayPro Courses, SayPro Jobs, SayPro Community Development, SayPro Products, SayPro Services, SayPro Consulting, and SayPro Advisory visit our website to www.saypro.online
Leave a Reply
You must be logged in to post a comment.